Daily maintenance of radial drilling machine
1、清洗机床外表及死角,拆洗各罩盖,要求内外清洁、无锈蚀、无黄袍,漆见本色铁见光。清洗导轨面及清除工作台面毛刺。检查补齐螺钉、手球、手板,检查各手柄灵活可靠性。
1. Clean the appearance and dead angle of the machine tool, remove and wash the covers. The inside and outside of the machine tool shall be clean, without rust and yellow robe. See the natural color iron for the paint. Clean the guide rail surface and remove the burrs on the working surface. Check the screws, handball and handboard, and check the flexibility and reliability of each handle.
2、摇臂钻床主轴进刀箱保养:检查油质,保持良好,油量符合要求。清除主轴锥孔毛刺。清洗液压变速系统、滤油网,调整油压。
2. Maintenance of main shaft feed box of radial drilling machine: check the oil quality, keep it in good condition, and the oil quantity meets the requirements. Remove the burr from the taper hole of the spindle. Clean the hydraulic transmission system, oil filter and adjust the oil pressure.
3、摇臂钻床摇臂及升降夹紧机构检查:检查调整升降机构和夹紧机构达到灵敏可靠。
3. Inspection for rocker arm and lifting clamping mechanism of radial drilling machine: check and adjust the lifting mechanism and clamping mechanism to be sensitive and reliable.
4、摇臂钻床润滑系统检查:清洗油毡,要求油杯齐全、油路畅通,油窗明亮。
4. Inspection for lubrication system of radial drilling machine: clean the linoleum, and ensure that the oil cup is complete, the oil path is smooth, and the oil window is bright.
5、摇臂钻床冷却系统检查:清洗冷却泵、过滤器及冷却液槽。检查冷却液管路,要求无漏水现象。
5. Inspection for cooling system of radial drilling machine: clean cooling pump, filter and cooling liquid tank. Check the coolant pipeline and make sure there is no water leakage.
6、摇臂钻床电器系统检查:清扫电机及电器箱内外尘土。关闭电源,打开电器门盖,检查电器接头和电器元件是否有松动、老化。检查限位开关是否工作正常。开门断电是否起到作用。检查液压系统是否正常,有无漏油现象。各电器控制开关是否正常。
6、 Electrical system inspection of radial drilling machine: clean the dust inside and outside the motor and electrical box. Turn off the power supply, open the electrical door cover, and check whether the electrical connector and electrical components are loose and aged. Check whether the limit switch works normally. Whether the door opening and power off work. Check whether the hydraulic system is normal and whether there is oil leakage. Check whether the electrical control switches are normal.
7、检查油质,保持良好,油量符合要求。
7. Check the oil quality, keep it in good condition, and the oil quantity meets the requirements.
8、清除主轴锥孔毛刺。
8. Remove the burr from the taper hole of the spindle.
9、清洗液压变速系统、滤油网,调整油压。
9. Clean the hydraulic transmission system, oil filter and adjust the oil pressure.
10、清除主轴上面的杂质,主轴上注油,保证主轴润滑。
10. Remove the impurities on the main shaft, and fill the main shaft with oil to ensure the lubrication of the main shaft.
枣庄美克机械有限公司生产的摇臂钻床质量上乘,深受客户欢迎。
The radial drilling machine produced by Zaozhuang Make Machinery Co., Ltd. is of high quality and well received by customers.